Nzs 3604 Roof Framing

Constructing Timber Outriggers Branz Build

Constructing Timber Outriggers Branz Build

Branz Now Recommend Using 10 Mm Of Xps As A Thermal Break For Slab Edge Insulation Concrete Slab Broken Concrete Insulation

Branz Now Recommend Using 10 Mm Of Xps As A Thermal Break For Slab Edge Insulation Concrete Slab Broken Concrete Insulation

Magroc Insulfound Magroc Building Insulation Exterior Cladding Building Systems

Magroc Insulfound Magroc Building Insulation Exterior Cladding Building Systems

Timber Framed Buildings

Timber Framed Buildings

Securing Buildings Against Uplift Branz Build

Securing Buildings Against Uplift Branz Build

Figure 1 Reinforcing For In Situ Concrete Foundation Wall For Single Storey Building Foundation Concrete Foundation

Figure 1 Reinforcing For In Situ Concrete Foundation Wall For Single Storey Building Foundation Concrete Foundation

Figure 1 Reinforcing For In Situ Concrete Foundation Wall For Single Storey Building Foundation Concrete Foundation

It provides methods and details that are used to design many nz timber framed houses and small buildings including many residential decks.

Nzs 3604 roof framing.

It is aligned with as nzs 1170 structural design actions and is referenced in acceptable solution for building code clause e2 external moisture e2 as1. 10 1 11 the building envelope wall and roof claddings. This modern profile metal sheet roofing is an example of a lightweight roof cladding. The bracing requirementfor monopitch roofs is addressed in nzs 3604 2011 timber framed buildingsparagraph 10 3 4.

The rafter span is 3 000 m and because this is a light roof the far right column of nzs 3604 2011 table 10 1 rafters for all wind zones see figure 2 can be used for rafter spacings at 1200 mm see note 4 in table 10 1. Nzs 3604 1999 incorporating amendment no. Print timber framed buildings. Very little area was often left as the body of the roof and it proved unrealistic to expect designers and installers to determine when and where extra fixings were required.

Nzs 3604 is new zealand s most sought after standard. Current the latest up to date edition. Simply stated it requires that bracing for monopitch roofs must comply with paragraphs 10 3 2 for light roofs or 10 3 3 for heavy roofs but it also includes an exemption. 1 and 2 new zealand standard timber framed buildings superseding nzs 3604 1990 and nzmp 3600 part 1 1992.

10 roof framing 11 building envelope roof and wall claddings 12 interior linings 13 ceilings additional information normative. You can follow nzs 3604 for structure and e2 as1 for the roof and wall claddings. Builders architects engineers designers and students will find it useful. A buildings shall be founded on good ground.

Nzs 3604 sets down construction requirements for timber framed buildings within the limitations specified in 1 1 2 nzs 3604 applies only to buildings within the following limitations this is not a complete list. B buildings shall be category iv or v buildings see table 1 1.

As1684 Residential Timber Framed Construction Bracing Example Timber Frame Construction Floor Framing Concrete Footings

As1684 Residential Timber Framed Construction Bracing Example Timber Frame Construction Floor Framing Concrete Footings

Roof Form And Framing Original Details Branz Renovate

Roof Form And Framing Original Details Branz Renovate

Figure 2 Reinforcing For Cantilevered Foundation Wall For 1 Or 2 Storeys Note Horizontal Reinforcing In Bond Beam 800 Building Foundation Wall Foundation

Figure 2 Reinforcing For Cantilevered Foundation Wall For 1 Or 2 Storeys Note Horizontal Reinforcing In Bond Beam 800 Building Foundation Wall Foundation

Veranda Rafter Fixings Branz Build

Veranda Rafter Fixings Branz Build

Source : pinterest.com